a:7:{i:0;a:2:{s:12:"faq-question";s:33:"A Toughened Epoxy That's Flexible";s:10:"faq-answer";s:473:"G/flex has been toughened. This gives it the ability to make structural bonds that can absorb the stresses of expansion, contraction, shock, and vibration. This epoxy is resilient and impact resistant. With a modulus of elasticity of 150,000 psi (WEST SYSTEM 105 Resin/205 Hardener has a modulus of elasticity of 450,000 psi), G/flex is more flexible and can deflect further before breaking than WEST SYSTEM 105/205, while being much stiffer than typical adhesive sealants.";}i:1;a:2:{s:12:"faq-question";s:21:"G/flex & Wet Surfaces";s:10:"faq-answer";s:129:"G/flex has the ability to glue damp woods. It can be used on wet surfaces, even underwater when applied with specific techniques.";}i:2;a:2:{s:12:"faq-question";s:33:"Adhesion to Hard-to-Bond to Woods";s:10:"faq-answer";s:258:"G/flex adheres tenaciously to difficult-to-glue hardwoods, both tropical and domestic varieties such as white oak and ipe. This is important since many of the exotic and tropical species now being used to replace traditional woods present bonding challenges.";}i:3;a:2:{s:12:"faq-question";s:31:"Bonding to Dissimilar Materials";s:10:"faq-answer";s:349:"G/flex is ideal for bonding a variety of materials, including dissimilar ones. It has a superior grip so that it can be used to bond to metals, plastics, glass, masonry, and fiberglass. This epoxy is ideal for repairs to aluminum boats and polyethylene and ABS canoes and kayaks. It can also be used to wet out and bond fiberglass tapes and fabrics.";}i:4;a:2:{s:12:"faq-question";s:12:"Using G/flex";s:10:"faq-answer";s:329:"G/flex is a simple two-part epoxy system. Resin and hardener are mixed in a 1-to-1 mix ratio by volume. It provides a relatively long open working time, yet it cures quickly and can be used in cool temperatures. Because it is simple to mix and use, this 2-part epoxy is an excellent starting point for customers new to epoxy use.";}i:5;a:2:{s:12:"faq-question";s:13:"Adhesion Data";s:10:"faq-answer";s:1163:"We often simplify adhesive bonds into two categories; primary bonds and secondary or chemical and mechanical bonds. Primary bonds occur when epoxy is applied to a previously applied layer of epoxy that has not been fully cured. The layers of adhesive will bond as if they were applied at the same time and mixed together. Mechanical bonds rely on the adhesion of the epoxy to a substrate. To visualize this, imagine the epoxy flowing into all of the imperfections and the sanding scratches of the substrate and locking into place. In reality, the forces are much more complex and beyond the scope of this article.

The fundamentals of achieving strong secondary bonds are the same whether the interatomic forces are understood or not. They include:
- Wet out the substrate. The epoxy must be able to flow and wet the surface. Surface contaminates can prevent this from happening.
- Let the epoxy cure in place. Clamps must remain in place and the joint can not be stressed until the epoxy cures.
- Use a high-strength epoxy. WEST SYSTEM® epoxy is a structural adhesive after it has been cured.

";}i:6;a:2:{s:12:"faq-question";s:34:"Tensile Adhesion of G/flex Epoxies";s:10:"faq-answer";s:10810:"Tensile stress on an adhesive is created when a load is applied perpendicular to the surface. The stress generated by the load may cause an adhesion failure that is much lower than the actual tensile strength of the glue. Tensile adhesion value is not the same as tensile strength. WEST SYSTEM epoxy is formulated to have high tensile strength for applications such as creating a strong fiberglass laminate, and high tensile adhesion to common substrates for strong bonds. WEST SYSTEM G/flex® is formulated to achieve the highest adhesion values. The Tensile Adhesion for G/Flex Epoxies on multiple substrates can be compared with this chart:

Tensile Adhesion of G/Flex Epoxies

Material	G/flex	Surface Prep/Conditions	Tensile Adhesion (psi)
G-10 high-density laminate	650	80-grit sand / dry surface	3459
G-10 high-density laminate	655	80-grit sand / wet surface	2473
1018 steel	650	80-grit sand / dry surface	3562
1018 steel	655	80-grit sand / wet surface	1772
Galvanized steel	650	100-grit wet sand	2562
Galvanized steel	655	100-grit wet sand	2929
Copper	650	80-grit sand	2334
Copper	655	80-grit sand	2685
Bronze	650	80-grit sand	2782
Bronze	650	Scotch Brite™ pad sand	2962
Bronze	655	80-grit sand	2936
316 Stainless Steel	655	80-grit sand	2522
ABS plastic	655	80-grit sand	1535
ABS plastic	655	80-grit sand, flame treat	1813
ABS plastic	655	Alcohol wipe, flame treat	3288
PVC	655	80-grit sand	1780
PVC	655	80-grit sand, flame treat	1813
PVC	655	Alcohol wipe, flame treat	2081
Polyethylene (HDPE)	655	80-grit sand	400
Polyethylene (HDPE)	655	80-grit sand, flame treat	1890
Polyethylene (HDPE)	655	Alcohol wipe, flame treat	2312
Polycarbonate (Lexan®)	655	80-grit sand	1870
Ipe	650	60-grit sand	2134
Ipe	655	Plane, isopropyl alcohol wipe x 3	2223
Teak, vertical grain	650	80-grit sand parallel to grain	1413
Teak, vertical grain	655	80-grit sand parallel to grain	1381
Teak, vertical grain	655	80-grit sand, alcohol wipe x 2	1503
White oak, vertical grain	650	80-grit sand	1935
White oak, vertical grain	655	80-grit sand	1780
White oak, vertical grain	655	Alcohol wipe x 2	2212
Purpleheart	650	60-grit sand parallel to grain	1731

";}}

Guías de selección